Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Just How to Install a Bath Tub Yourself: Removing as well as Replacing.
Blog Article
We have stumbled on the article on How to Install a Bathtub directly below on the net and accepted it made perfect sense to share it with you on this site.
Setting up a bathtub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably difficult job. If the old tub is easily accessible, the job can move immediately; if you have to open up a wall to eliminate the old bathtub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the brand-new one. Make sure you have actually certified yourself for the work and are comfortable trying it. Rather than employing a contractor to take control of a halfway-completed task, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your shower room if you have already gotten a new bathtub and also don't require to transform the plan of your previous supply of water pipes.
Your devices as well as material checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be rather troublesome as a result of the limited accessibility that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to proceeding to fit the new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washing machines remain in place in between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap ports. The former type needs to be linked to the faucet finishes initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bathtub
Making use of both wooden boards under its feet, put the tub in the required placement. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be achieved by inspecting the spirit level and also changing the feet on the tub until the level reads degree.
To set up taps, fit all-time low of the outermost adaptable faucet connector to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Activate the water system and examine all joints as well as new pipework for leakages and also tighten them if needed. Fill the bathtub as well as additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the tub ought to wait till the tub has actually been used a minimum of once as this will certainly settle it right into its final placement.
Preparing for the Installment
To start with, the supporting frame provided with the bath needs to be fitted (if needed) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is necessary to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is additionally practical to fit a sustaining plate under the taps device to avoid pressure on the bathtub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently prepare to be fitted in its final placement.
Tiling Around the Tub
In the location where the bath meets the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the installation can move enough to crack a rigid seal, triggering the water to pass through the wall surface between the bath as well as the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly load the bath tub with water prior to securing, to allow for the movement experienced when the tub is in use. The sealant can fracture fairly early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently offered on the market. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads about Installing A Bathtub, I imagined sharing that excerpt was really useful. I beg you take the opportunity to promote this blog entry if you liked it. I praise you for your time. Please pay a visit to our website back soon.
Book My Estimate Report this page